Battery regeneration for Mountfield Alpina Model T327 10.8V mower

Fits the following mower models

AG 53STGRDE 4X1 (2019), AL6 51 VAQE (2020), BL 510 SE (2019), BL 510 SE (2020), BL 510 SQE (2019), BL 510 SQE (2020), BTR 50TEA (2019) , Combi 48 SEQ (2019), Combi 48 SEQ (2020), COMBI 48 SEQ (2021), COMBI 48 SVQ (2019) [2L0487848 / ST1P], COMBI 50 SVEQ (2019), Combi 50 SVEQ (2020), COMBI 53 SEQ (2019) [295536548 / ST1], COMBI 53 SEQ (2019) [295536548 / ST1P], COMBI 53 SEQ (2020), COMBI 53 SEQ (2020) [295536548 / ST1P], COMBI 53 SEQ (2021) [2L0536548 / ST1], COMBI 53, SEQ (2021) [2L0536548 / ST1P], ED 53GRDE 4x1 (2020), EP 464TVGI (2020), EP 534 TEG (2019), GD85907 / TTDE-F170 (2019), GD85907 / TTDE-F170 (2020), HW 46 ES 3 (2020), MULTICLIP 47 SEQ (2019), Multiclip 47 SEQ (2020), Multiclip 50 SXE (2020), MULTICLIP 50 SXE (2019), MULTICLIP 50 SXE (2021), OEKONOMIC 5120 SEWMK (2020), PG50STVE (2020), PM 486TIVX (2020), S461R PD LS (2019), S461R PD LS (2020), S481 PD LS (2019), S481 PD LS (2020), S501R V LS (2020), SG 50TXE (2019), SG 50TXE (2020), SP46 LS (2019) [295496548 / M19], SP46 LS (2019) [2L0486 548 / M19], SP46 LS (2020), SP533 LS (2019), SP533 LS (2020), SP551 V LS (2019), SP551 V LS (2020), ST 170 LS (2020), TURBO 53 L (2019) , TWINCLIP 50 SEQ (2019), VL 50 TVE (2020), WBE 170 Lion (2020), WBE170LS (2019), XC 48 SWE (2020)

Replaces batteries with the symbols

BPS 12

IS STIGA BATTERY REGENERATION COMPLICATED?

How does the regeneration of a Stig battery used in power tools look like? All battery cells are subject to replacement. Then they must be connected to the electronic system of the battery (applies to li-ion batteries) and to the terminals of the contacts. As part of regeneration, resistors and thermistors are also checked and, if necessary, replaced with new ones. For a qualified service technician, this is not the slightest problem.

STIGA BATTERY REGENERATION STEP BY STEP

• removal of the battery cover;
• disassembly of used cells;
• clean the case;
• preparing a package of new cells (welding);
• check resistors and thermistor (replace if necessary);
• installing new parts in the housing;
• assembling and screwing the casing;
• final test of battery health.

BENEFITS OF BATTERY REGENERATION

The first and obvious advantage is saving money. The cost of regeneration is incomparably lower than the purchase of a new battery. However, this is not the only benefit. It is very important to keep the original housing, which will certainly fit your power tool and the charger used so far. Additionally, as part of regeneration, the same or even greater battery capacity can be obtained, which guarantees efficient operation of the power tool.

HOW LONG DOES IT TAKE TO REGENERATE THE BATTERY?

The order fulfillment time depends on two issues: the type of battery and the current order load. The second factor may extend the order processing time, but the standard regeneration time is usually:

• 2-3 days (7.2-18V batteries)
• up to 5 working days (batteries 24-36V).

WARRANTY

Each regeneration is covered by a written warranty. Depending on the type and quality of cells used for regeneration, it ranges from 6 months to two years.

How to have the battery regenerated in our company?

To meet your expectations, we have prepared four forms of ordering the battery regeneration:

1. To place an order through our website.
2. Sending us the equipment with the attached order form .
3. Sending us the equipment with the attached contact details and address.
4. Sending us the battery with filling in our internet battery regeneration order form which is quick and convenient

OUR ADDRESS
Lupo sp. z o.o.
ul. Strzeszyńska 30 B
60-479 Poznań